Home / Washer repair / Whirlpool / Duet

Whirlpool Duet washer repair

Front-load washer line sold in the 2000s and 2010s, usually paired with a matching Duet dryer. We repair them at your home across Charleston, North Charleston, Mount Pleasant, Summerville and the Lowcountry.

From our service calls

What fails on the Duet

  • Door boot seal

    The gasket traps water and lint, smells and tears.

  • Drain pump

    Pump filters clog and the washer shows a long drain code.

  • Drum spider and bearings

    A loud roar in spin means the bearings or the rear drum support are failing.

  • Control board

    Older units develop board faults after power surges.

In Charleston

Lowcountry humidity means front-load door seals and dispensers mildew faster than in drier climates. Leave the door ajar between loads and wipe the seal weekly.

Owner tip: Leave the door open after washing and clean the pump filter every few months.

Repairs

Common repairs for this washer

On the display

Whirlpool washer error codes

F0 E2 Whirlpool · Washer

Too many suds

Cause: Too much detergent, or non-HE detergent in an HE washer.

What to do: Let the washer finish its rinse routine. Use only HE detergent and less of it.

You can check this yourself Book a repair
F0 E5 Whirlpool · Washer

Off-balance load

Cause: The load has shifted to one side of the basket.

What to do: Open the lid, spread the laundry evenly and restart.

You can check this yourself Book a repair
F1 E1 Whirlpool · Washer

Main control fault

Cause: The main electronic control has an internal fault.

What to do: Unplug the washer for 2 minutes. If the code returns, the control board needs diagnostics.

Needs a technician Book a repair
F21 Whirlpool · Washer

Long drain

Cause: The drain pump filter is clogged or the drain hose is kinked.

What to do: Unplug the washer, open the lower access panel and clean the pump filter. If the code returns, the pump needs replacing.

You can check this yourself Book a repair
F3 E1 Whirlpool · Washer

Pressure sensor fault

Cause: The water level sensor or its hose is faulty or disconnected.

What to do: The pressure hose and sensor need checking by a technician.

Needs a technician Book a repair
F5 E2 Whirlpool · Washer

Door won't lock

Cause: The door lock assembly is faulty or something is caught in the latch.

What to do: Make sure nothing is caught in the door and close it firmly. If the code stays, the lock needs replacing.

Needs a technician Book a repair
F6 E2 Whirlpool · Washer

Communication error

Cause: The main control and the motor control are not talking to each other.

What to do: Unplug for 2 minutes. If it returns, the wiring harness and boards need testing.

Needs a technician Book a repair
F7 E1 Whirlpool · Washer

Basket speed fault

Cause: The motor can't reach the expected speed: overloaded basket, worn drive or faulty motor sensor.

What to do: Remove some laundry and restart. If it returns, the drive system needs service.

You can check this yourself Book a repair
F7 E5 Whirlpool · Washer

Shifter fault

Cause: The shifter that switches between agitate and spin has failed or lost its signal.

What to do: The shifter assembly needs replacing.

Needs a technician Book a repair
F8 E1 Whirlpool · Washer

No water detected

Cause: The faucets are closed, the inlet screens are clogged or the pressure is low.

What to do: Open both faucets fully and check the inlet hose screens. If it continues, the inlet valve needs testing.

You can check this yourself Book a repair

All Whirlpool washer codes

Call Book a repair