Home / Washer repair / Whirlpool / Cabrio

Whirlpool Cabrio washer repair

High-efficiency top-load washer with a low-profile wash plate instead of an agitator, sold mainly from the late 2000s to the 2010s. We repair them at your home across Charleston, North Charleston, Mount Pleasant, Summerville and the Lowcountry.

From our service calls

What fails on the Cabrio

  • Shifter / actuator

    The drive shifter that switches between agitate and spin fails and the washer shows a shifter code or will not spin.

  • Lid lock

    The lid lock wears and the washer stops before spin.

  • Suspension rods

    Worn rods make the tub bang during spin.

  • Basket drive and bearings

    A rumbling noise during spin means the tub bearing is going.

In Charleston

Lowcountry humidity means front-load door seals and dispensers mildew faster than in drier climates. Leave the door ajar between loads and wipe the seal weekly.

Owner tip: Run the cleaning cycle monthly and keep loads balanced: Cabrio tubs are sensitive to one heavy item.

Repairs

Common repairs for this washer

On the display

Whirlpool washer error codes

F0 E2 Whirlpool · Washer

Too many suds

Cause: Too much detergent, or non-HE detergent in an HE washer.

What to do: Let the washer finish its rinse routine. Use only HE detergent and less of it.

You can check this yourself Book a repair
F0 E5 Whirlpool · Washer

Off-balance load

Cause: The load has shifted to one side of the basket.

What to do: Open the lid, spread the laundry evenly and restart.

You can check this yourself Book a repair
F1 E1 Whirlpool · Washer

Main control fault

Cause: The main electronic control has an internal fault.

What to do: Unplug the washer for 2 minutes. If the code returns, the control board needs diagnostics.

Needs a technician Book a repair
F21 Whirlpool · Washer

Long drain

Cause: The drain pump filter is clogged or the drain hose is kinked.

What to do: Unplug the washer, open the lower access panel and clean the pump filter. If the code returns, the pump needs replacing.

You can check this yourself Book a repair
F3 E1 Whirlpool · Washer

Pressure sensor fault

Cause: The water level sensor or its hose is faulty or disconnected.

What to do: The pressure hose and sensor need checking by a technician.

Needs a technician Book a repair
F5 E2 Whirlpool · Washer

Door won't lock

Cause: The door lock assembly is faulty or something is caught in the latch.

What to do: Make sure nothing is caught in the door and close it firmly. If the code stays, the lock needs replacing.

Needs a technician Book a repair
F6 E2 Whirlpool · Washer

Communication error

Cause: The main control and the motor control are not talking to each other.

What to do: Unplug for 2 minutes. If it returns, the wiring harness and boards need testing.

Needs a technician Book a repair
F7 E1 Whirlpool · Washer

Basket speed fault

Cause: The motor can't reach the expected speed: overloaded basket, worn drive or faulty motor sensor.

What to do: Remove some laundry and restart. If it returns, the drive system needs service.

You can check this yourself Book a repair
F7 E5 Whirlpool · Washer

Shifter fault

Cause: The shifter that switches between agitate and spin has failed or lost its signal.

What to do: The shifter assembly needs replacing.

Needs a technician Book a repair
F8 E1 Whirlpool · Washer

No water detected

Cause: The faucets are closed, the inlet screens are clogged or the pressure is low.

What to do: Open both faucets fully and check the inlet hose screens. If it continues, the inlet valve needs testing.

You can check this yourself Book a repair

All Whirlpool washer codes

Call Book a repair