Home / Problems / Washer / Washer won't spin

Washer won't spin

If the washer fills and washes but never spins, the cause is usually an unbalanced load, a lock that never engaged, or a worn belt or drive part.

Most likely first

Common causes

  1. 1

    Unbalanced load

    One heavy item such as a rug or a soaked towel throws the drum off center, so the washer refuses to spin fast.

  2. 2

    Water not drained

    Most washers will not spin with water still in the tub.

  3. 3

    Door lock or lid switch failure

    The spin is blocked for safety until the lock reports closed.

  4. 4

    Worn drive belt or motor coupler

    The motor runs but the drum does not turn with it.

  5. 5

    Shifter or clutch fault

    On top loaders a shifter that does not change to spin mode leaves the basket still.

In Charleston

Lowcountry humidity means front-load door seals and dispensers mildew faster than in drier climates. Leave the door ajar between loads and wipe the seal weekly.

Safe checks before you book

  • Redistribute the load or remove one heavy item and run Spin only.
  • Make sure the tub drains first.
  • Listen for the click of the lid lock when the cycle starts.
  • Turn the drum by hand with the power off and feel for grinding or no resistance at all.

When to call us: Call us if the drum is stuck, you hear grinding, or the washer shows a shifter, motor or lock code.

Repairs that fix it

What the technician may do

Shows a code?

Related washer error codes

F5 E2 Whirlpool · Washer

Door won't lock

Cause: The door lock assembly is faulty or something is caught in the latch.

What to do: Make sure nothing is caught in the door and close it firmly. If the code stays, the lock needs replacing.

Needs a technician Book a repair
F8 E1 Whirlpool · Washer

No water detected

Cause: The faucets are closed, the inlet screens are clogged or the pressure is low.

What to do: Open both faucets fully and check the inlet hose screens. If it continues, the inlet valve needs testing.

You can check this yourself Book a repair
dL Whirlpool · Washer

Door or lid lock fault

Cause: The lock can't engage, often because something is in the way or the lock has failed.

What to do: Check nothing is caught in the door or lid. If the code stays, the lock needs replacing.

You can check this yourself Book a repair
uL Whirlpool · Washer

Unbalanced load

Cause: The washer is trying to rebalance the load.

What to do: Let it finish. If it stops, redistribute the laundry by hand.

You can check this yourself Book a repair
3C Samsung · Washer

Motor fault

Cause: The drive motor is overloaded or its sensor has failed.

What to do: Reduce the load and restart. If it returns, the motor needs service.

Needs a technician Book a repair
4C Samsung · Washer

No water coming in

Cause: A faucet is closed or the inlet hose is kinked.

What to do: Open the faucets, straighten the hoses and rinse the inlet screens. If nothing changes, the inlet valve is faulty.

You can check this yourself Book a repair
4C2 Samsung · Washer

Hot water on the cold inlet

Cause: The hot water hose is connected to the cold inlet.

What to do: Swap the inlet hoses so cold water feeds the cold inlet.

You can check this yourself Book a repair
01Why is my washer doing this?

If the washer fills and washes but never spins, the cause is usually an unbalanced load, a lock that never engaged, or a worn belt or drive part.

02What can I check myself first?

Redistribute the load or remove one heavy item and run Spin only. Make sure the tub drains first. Listen for the click of the lid lock when the cycle starts. Turn the drum by hand with the power off and feel for grinding or no resistance at all.

03When should I call a technician?

Call us if the drum is stuck, you hear grinding, or the washer shows a shifter, motor or lock code.

04What does a repair visit cost?

One flat service call covers the trip and a full diagnosis. You get an exact quote for parts and labor before any work starts.

Call Book a repair